50Kgf - Jet Thruster JT50 Bow or Stern (Horizontal pump)

50 Kgf for Bow or Stern:

Explanation towards all options: Read thoroughly and select:

- All standard parts are mentioned in diagram below. They are required for the installation and included in the price

- Specific and required parts such as the nozzles etc must be selected with help the check-boxes

- Additional parts, and important products are displayed, and can be selected if you choose to order them

The check boxes enable you to select all required parts. After completing them your JT50 system is ready to be installed.

---

The following parts in this table are already included in the product price!

Pump unit JT50 Compact	WS-JT50-50-24V	1x
3-Way directional valve	WS-V-100-58-25	1x
Pump outlet:	Select at the Check Boxes	1x
Water inlet 3" (Composite)	WS-I-302-GF-00	1x
Elbow 90-degree 3"=>2.5"BSP	WS-I-346-GF-00	1x
Ball Valve 2,5" (SS316)	WS-I-105-00	1x
Hose connector 2,5" (SS316)	WS-I-310-00	1x
Hose 3"/76mm L=1m	WS-I-312-00	1x
Hose clamp 77-94	WS-I-331-SS	2x
Hose clamp 60-76mm	WS-I-116-SS	6x
Hose connector 58mm (Composite)	WS-I-164-GF-00	2x
Elbow 45-degree 2"BSP (Composite)	WS-I-316-GF-00	2x
Ball Valve 2" (SS316)	WS-I-321-00	2x
Hose 58mm (Dedicated Jet Thruster hose size)	WS-I-113-58	10m/33ft
Nozzles	Select at the Check Boxes
Fuse holder + fuse	WS-I-254-01	1x
Battery Main Switch	WS-E-102-00	1x
Series parallel switch	WS-I-356-00	1x
Control panel with joystick	WS-I-150-25	1x
Jet Thruster digital controller (Optional selected item)	WS-E-300-00	1x
Cable: Controller to Joystick	WS-E-301-00	1x
Cable: Controller power cable	WS-E-304-00	1x

Explanation towards required choices to complete the JT50 system

---

Standard: 12V Plug & Play Controls:

We standard provide a Plug & Play wire harness to setup the connection between the Control panel - Pump unit and Directional 3-way valve. All 3 have pigtails with high quality automotive waterproof/sealed Deutsch connectors. This allows a Plug & Play connection and easy installation. It's important to mention that this setup is for a Bow Jet Thruster or Stern Jet Thruster setup only. In case you prefer to (later) upgrade this Single Jet Thruster into a Combi system for Bow and Stern, do NOT select this electrical setup. Choose a Setup with the Optional controller instead.

Optional: Jet Thruster Single in combination with the 12V Digital Jet Thruster controller:

In case you later on want to upgrade the Single Jet Thruster system into a Combi system for Bow AND Stern, it's important to select the optional 12V Digital Jet Thruster controller. In case you want to connect an existing Bow Thruster system to a Single Stern Jet Thruster system, a Jet Thruster controller can be used to operate this existing bow thruster. A dedicated cable between the existing Bow Thruster and the Jet Thruster controller is available.

---

Motor: Select 24V/48V: Choose at which voltage you want to run the Jet Thruster pump unit.

Note, most boats have a 12V circuit. This how ever doesn't mean you must have a 12V Jet Thruster motor:

With a 24, or 48v dedicated battery pack, it's possible to have a bank in a higher voltage and have it charged by your 12, or 24v alternator.

Use the Series-Parallel Switch or/and the Mac Plus converter charger to enable a dedicated battery bank with higher voltage in a 12V circuit.

A: 24V Pump Motor(Standard) 2-3 minutes continuous run-time

Note 1: In case of a 12V circuit: Order Series Parallel Switch or Master Volt Mac Plus step up charger (Not required in case of a 24V circuit)

Note 2: Order 2x Optima Yellow Top batteries to create a dedicated 24V battery bank

B: 48V Pump Motor(Popular choice for charter boats) 3-4 minutes continuous run-time and 10% more thrust power.

Note 1: In case of a 12V circuit: Order a Series Parallel and a Mastervolt Mac Plus step up charger

Note 2: In case of a 24V circuit: Order a Series Parallel Switch

Note 3: Order 4x Optima Yellow Top batteries to create a dedicated 48V battery bank

---

Pump head position:

The Jet Thruster pump head can rotate. This enables you to select the orientation which is best for the installation. The pump head position can be ordered in position you would like it to be in. If later on you prefer to change, this is no problem. All Jet Thruster pump heads can be changed. Read out manual how to change the postion.

C: Position #1 (outlet shroud pointing up)

D: Position #2 (outlet shroud pointing side-way)

---

Pump outlets:

Because each project is often a custom project, we have several custom components you must chose from. Depending on the pump head position at point C and Point D, you can choose from 2 different pump outlet types.

E: Pump outlet straight

F: Pump outlet 90-degree elbow

---

Nozzles:

G - P

Nozzles are a crucial part in any Jet Thruster installation:

The water flow is directed to nozzles which are located Forward and Aft in the boat, just below the water line. Because each hull is different, and interiors may vary, we have created a series of nozzles with different flange angles in order to have the optimum nozzle for your boat. We have created a Informative Website page towards this subject in which we full explain how to select the correct Nozzle type:

Select a nozzle type with help of the tools we created: Go directly the to the Nozzle page with this link:

---

Batteries:

Optima batteries are the best choice for powering Jet Thruster systems. These batteries are Small, powerful and have excellent deep cycle capabilities. We recommend Optima only for Jet Thruster systems

Q:(Set of 2) to create a dedicated 24V bank

R:(Set of 4) to create a dedicated 48V bank

---

S: Series Parallel Switch:

In order to charge the dedicated 24V jet Thruster battery bank, the series parallel is a reliable automatic mechanical switch. It is a standard item on the Jet Thruster JT50 part list.

However: If you already have a 24V circuit to charge the dedicated 24V Jet Thruster battery bank, you do not need to order this switch. Deselect the switch by ticking the Minus-box, to exclude it from the package price

---

T: Mastervolt Mac Plus Step up Charger 12-to-24V

The Mastervolt 12-to-24V Step up Charger is a Intelligent charger which converts 12V energy from your Service Battery bank into 24V to charge the dedicated battery bank. It does this only when your Service batteries are being charged if you run your engine, your service batteries are being charged, or in case your boat is connected with the land power. The Mastervolt Mac Plus will run an intelligent program to keep the dedicated Jet Thruster battery bank in optimum condition. The installation of this charger is very easy. It will enable a setup for the dedicated battery bank with minimum amount of battery cable. We endorse the use of this charger.

Note: When you select the Mastervolt Mac Plus option, you have to remove the Series-Parallel switch (Option S) because the Mac Plus will replace it in that case)

T1: Cristec Step up Charger 12-to-48V

The Cristec 12-to-24V Step up Charger is a Intelligent charger which converts 12V energy from your Service Battery bank into 48V to charge the dedicated battery bank. It does this only when your Service batteries are being charged if you run your engine, your service batteries are being charged, or in case your boat is connected with the land power. The Cristec YPOWER will run an intelligent program to keep the dedicated Jet Thruster battery bank in optimum condition. The installation of this charger is very easy. It will enable a setup for the dedicated battery bank with minimum amount of battery cable. We endorse the use of this charger.

Note: When you select the Cristec YPOWER option, you have to remove the Series-Parallel-switch (Option S) because the Cristec YPOWER will replace it in that case)

---

U: Composite 2" Ball Valves instead of standard Stainless steel 2" ball valves

The use of Composite products is rapidly increasing in the marine industry. The reason is obvious. Composites work very well in Salt water environments, and valves will not deteriorate due to the corrosive nature of sea water. In case your boat is on salt water, we recommend composite valves over Stainless steel valves. We endorse the use of Composites based upon the unique and reliable characteristics and the positive feedback from the market.

---

V: Zinc Anode for Pump Outlet (WS-CP-001-00 + WS-P-156-00)

There are Stainless steel parts in and to the pump which benefit from a cathodic protection by use of Zinc in case of use in salt water. In order to protect the pump shaft, stainless steel impeller, pump outlet and pump inlet, we have developed an Anode kit to protect these parts.

- WS-P-156-00: The 2" threaded side will screw into the 2" threaded pump outlet

- WS-CP-001-00: The Zinc Anode kit includes a composite holder in which a zinc anode is present. With the provided cable set, all necessary parts are connected with the zinc.

---

W: Wet Wipes

All threaded parts are connected with a Poly-Urethane sealant. Parts straight BSP threads (no NPT) and after all threads have been de-greased and thoroughly cleaned, all threads are covered with a rich amount of the adhesive. Both Male and Female threads must be fully covered. Inevitably, the sticky and very difficult to remove Poly-urethane sealant will get on your hands, tools and parts. Directly after you connected the parts, these wipes will allow you to wipe off the sealant from any surface. Try this with paper or cloth and you'll end up with a big mess. Use the wipe and deliver a spotless and professional installation. Highly recommended to have this bucket with 150 little towels around.

---

X: PU-Sealant

The only good way to connect install the BSP threaded parts, and nozzle and water inlet flanges is with use of a Poly-Urethane sealant. We recommend the Wurth Marine sealant.

---

Y: Hose (Minus length)

The installation kit provides 10M/33ft of Marine water hose in the right quality. Possible the standard length is too long, or not long enough. We offer the possibility to decrease hose length in the installation kit.

- Tick the Y box change from standard 10,/33ft into 5m/16ft. In this case we will ship a total of 5M/16ft

Y1 : Hose (Minus length)

- Tick the W1 box in case you do not want to buy hose

---

Z: Hose (Plus length)

The installation kit provides 10M/33ft of Marine water hose in the right quality. In case 10M/33ft in not long enough you can order additional hose in the Installation kit

- Tick the Y box and reduce the hose length from a standard 10m/33ft into 5m/16ft. In this case we will ship a total of 5M/16ft